jamescwifbのブログ

アクセスカウンタ

zoom RSS How To Make A Baby Crib Set

<<   作成日時 : 2012/05/22 08:32   >>

ブログ気持玉 0 / トラックバック 0 / コメント 0

Reference Article: How To Make A Baby Crib Bumper



How To Make A Baby Crib Set

1

<figure>

Serenity for baby

</figure>

FITTED CRIB SHEET: Sewing machine ready? Let us start with the basic fitted baby crib sheetHow to produce a Baby Crib Set. You will want to begin by removing a 9" square from each and every corner the 70" x 45" cotton fabric. Now using your sewing machine, sew the corners. The corners are referred to as

babygirl bedding

the pressure points that need to withstand wear and tear when you take the sheets on and off the mattress so please be sure to sew this twice or 3 times over. Fold the edges, sew around

baby bedding for girl

the crib sheet with a zig zag stitch. Remember this part does not have to be perfect because this portion of the sheet will likely be tucked below the mattress. find the center of your elastic and sew it to the center of your corner seam. Sewing from the center seamHow to produce a Baby Crib Set, stretch out the elastic while sewing. Ensure you are nevertheless utilizing zig zag seam so there is stretch in your thread Voila! You are now finished with all the fitted sheet!


2

<figure>

Sleeping beauty

</figure>

BABY QUILT: Pre wash the fabrics separately. Ensure the fabric completely dried and iron it afterwards, adding spray starch to fabric.

It is time to cut the fabric! Place the fabrics in form of a pile, one over another on the place mat (or a table). Get your ruler, measure and cut 2" x 2" pieces with your rotary cutter. Cut as many pieces as you want in order to cover the size with the quilt you want. Stitch the squares together to form a big square, this is called, "The Block." Sew all the pieces to form precisely the same blocks. You can begin to sew all of the blocks to every other until you get the desired size of the quilt. See how easy! Spot your batting material above the piecing you just created. The top rated of the piecing really should be facing the mat (or the table) as well as the stitched side should certainly get along the batting. Spot your lining fabric more than this.) You will have to stitch all 3 layers to every single other using the help of the handy-dandy sewing machine. For the beginner, stitch around the basic blocks, stitching all more than the quilt.

Bind all the sides together with a piece of the fabric. Now you should really be proud because you've just created a quilt for your baby.


3

<figure>

Sporting themes

</figure>

BABY CRIB BUMPER: Time to create a pattern for your crib bumpers. Measure the crib. You need to know the length from the crib, how extended each side is. For your pattern, you will need to add 1/2 longer on every single side so however the length or width add 1". the width of the printer paper (eight 1/2"). To create the pattern, tape the pattern papers finish on finish. Trim them to create them the length from the side in the crib plus a single inch. If you are creating them width wise larger than an eight 1/2" sheet of paper then you will have to make two and tape them with each other to produce the appropriate dimensions. Repeat this step all over again for the width side from the crib. Return for the crib, hold up the pattern papers towards the crib, mark where the crib bumper pads ties will be. You need to hold it up for the crib so you know the tie will line up using the bars. Lay your fabric down on flat workspace. You will need to fold the fabric in half to ensure that the front is facing inwards towards itself. Now lay a sheet of cotton batting more than this. The batting can be whatever weight you want. Depending on how thick you wish your bumpers to become. Pin the crib bumpers patterns down over each the fabric and the batting. Use the patterns as your guide to cut the fabrics and batting. Cut two sets for the sides in the crib and two for the ends then pin these back together.

Cut your ribbon into eight to ten inch lengths. Make these exactly the same length, you will need to have 12 pairs of lengths in ribbon. Pin the ribbons in location where you want them to be sewed. The ribbons need to be laid inside in-between your fabric pieces. Pin a single set to the top rated and 1 to the bottom exactly where you marked off on the pattern for the ties to become sewn. 1 inch need to stick out from the leading plus the bottom of the fabric but the rest must be tucked neatly inside. If you want, you can pin the ends in spot so they don't accidentally get sewn in location. Sew each piece by stitching around the entire outside of every pattern piece, leaving a 1 to two inch opening for turning the fabric inside out. Make positive and stitch 1/2 inch in from the edge to go along with the pattern you made. You had 1 inch added to each and every pattern piece. Turn each and every piece so the fronts are facing outside. Pin the openings shut and hand stitch them. To finish, you need to pin the crib bumpers together and hand stitch them carefully. When you location the bumper pads in to the crib have the hand stitched edges facing inwards that way they won't be observed.


How To Make A Baby Crib Set



月別リンク

ブログ気持玉

クリックして気持ちを伝えよう!
ログインしてクリックすれば、自分のブログへのリンクが付きます。
→ログインへ

トラックバック(0件)

タイトル (本文) ブログ名/日時

トラックバック用URL help


自分のブログにトラックバック記事作成(会員用) help

タイトル
本 文

コメント(0件)

内 容 ニックネーム/日時

コメントする help

ニックネーム
本 文
How To Make A Baby Crib Set jamescwifbのブログ/BIGLOBEウェブリブログ
文字サイズ:       閉じる